Description

This is a working pair of Dynaudio Acoustics BM5 passive nearfield monitors, made in Denmark, with the original drivers still in the boxes. They are sold as a pair, the price is on request, and both cabinets are in stock right now.

I want to be plain about one thing before the details: these are the passive BM5, not the BM5A. That distinction matters more than most listings admit, and it changes what you need to buy alongside them.

The label tells you what you need to know

The rear panel of each cabinet carries the original printed plate: dynaudioacoustics® BM5, followed by Nominal Impedance: 4 ohms and Amplifier power: 50 – 100 RMS Watts. Below that sits a red sticker with the serial and the words Made in Denmark. One cabinet reads serial 849635. That plate is the single most useful piece of information on the speaker, because it is Dynaudio’s own statement about what to drive them with.

Four ohms is an honest number from the manufacturer, not a guess. It means you want an amplifier that is comfortable into a low-impedance load and that can deliver 50 to 100 watts per channel cleanly. Small chip amps rated “100W” at one kilohertz into eight ohms are not that amplifier.

What is actually inside the cabinet

We opened one cabinet to photograph it, and the drivers are the ones you would hope to find:

  • Woofer: Audio Technology 17W75 BMS DA, printed label with lot number NO: 84841 and Made in Denmark. The 17 in the model number refers to a 17 cm cone, which works out to the 6.5-inch class.
  • Tweeter: Dynaudio T100 DA, with the magenta DYNAUDIO and AUTHENTIC FIDELITY print, an Alnico magnet ring marked ALNICO MAGNET, and a factory tag reading NO: 81301.
  • Cabinet: MDF with a matte black finish and a rear port.
  • Terminals: a recessed cup on the back with a pair of brass binding posts, banana-compatible.

The Alnico magnet on the tweeter is worth pausing on. Alnico was expensive and was largely abandoned in the 1980s, so finding it in a monitor of this vintage is a genuine indicator of the era and the price bracket these were built for. I am not going to tell you it sounds like magic. I will tell you that it is a real, verifiable detail that most used listings for these boxes never mention because the seller has never taken one apart.

Why the passive version suits some rooms better than active monitors

Active monitors are easier: plug in, done. Passive gives you a choice, and that choice is the reason people still hunt for BM5s. If you already own a good amplifier you trust, a passive pair lets you use it, which is something no active monitor can offer. If you are building a room around a specific amp’s character, that matters.

The trade-off is real, though. You need an amp with headroom, you need to think about cable runs, and you inherit the amp’s noise floor. Anyone who wants to unbox a monitor and start mixing should look at an active pair instead. For a reference point in our own stock, a KRK V6 Series 3 active pair is the plug-and-play route, and a Barefoot Sound MicroMain27 Gen2 sits at the other end of the budget entirely.

Condition, honestly stated

The cabinets show light wear. Grill cloth is intact on both, the matte black finish has no deep gouges, and the binding posts are clean with no corrosion. One woofer surround shows slight discoloration consistent with age rather than abuse. There is a light scuff on the top edge of one cabinet.

What I cannot tell you: we have not swept them, we have not measured impedance, and we have not run a frequency response plot. The drivers are original and unbroken, the cabinets are solid, and the photos show exactly what is there. If you want a specific measurement before committing, say which one and we will run it.

What I will not put in this listing

You will find BM5 spec sheets online quoting frequency response, sensitivity, crossover points and weight. I do not trust any of them enough to reprint here. Dynaudio’s own archived pages for the early Acoustics series are largely gone, and the third-party numbers I can find contradict each other. Rather than copy a figure I cannot verify, I am leaving those blank. The impedance and the recommended amplifier power range come straight off the label on the cabinet, and that is the limit of what I will state as fact.

Shipping and export

Both cabinets are here in stock and can ship as a pair or singly, though they are a matched set and I would rather they stayed together. We ship from China to most markets, and we quote freight after you tell us the destination port and whether you want door delivery. Voltage is not a factor here since these are passive, which actually makes them simpler to export than any powered monitor.

Price is on request. Tell us the destination and the quantity and you will get a number with freight broken out, not a lump figure.

Related gear worth a look

Key takeaways

  • Dynaudio Acoustics BM5, passive two-way nearfield, made in Denmark, sold as a pair.
  • Rear label states 4 ohms nominal and 50–100 watts RMS recommended amplifier power.
  • Original drivers confirmed by opening a cabinet: Audio Technology 17W75 BMS DA woofer and Dynaudio T100 DA Alnico tweeter.
  • Not tested or measured by us; photos document the actual condition.
  • Price on request, in stock, shipping from China.
Good In Stock

Dynaudio Acoustics BM5 Passive Studio Monitor, Pair (Used, In Stock)

Ask for price

FOB price from China. Shipping quoted per destination.

Listed on October 31, 2026
Learn more

Related Q&A & Guides