Daily Q&A

Where Should You Put Speakers to Stop Feedback at a Small Gig?

Answered on October 30, 2026

Feedback happens when a microphone hears the speaker it is amplified through. The fix is geometry first: mains 1.5-2 m in front of the vocal mics, tilted down 10-15 degrees toward the audience, and never behind the singer. Do that and you gain 3-6 dB of headroom before feedback starts, which is usually enough to stop it entirely at a small gig.

People reach for the 31-band EQ first. That is the slow way, and it costs you tone.

How far should the mains be from the vocal mics?

At least 1.5 m, measured from the mic capsule to the front of the speaker. Doubling that distance gives you about 6 dB of feedback margin, because the mic hears the speaker 6 dB quieter. In a 100-capacity room you usually cannot manage more than 2-2.5 m, which is why cardioid mics with tight pickup patterns matter so much.

  • Cardioid dynamic mic: usable at 1.5 m with 3 dB margin.
  • Supercardioid: usable at 1.2 m, but more sensitive at the rear null.
  • Omnidirectional: will feedback at almost any distance. Do not use one on a loud stage.

Why does angling the speakers inward help?

Because the mic is not in the speaker’s coverage pattern. A 12-inch powered box typically covers 90 degrees horizontally and 60 vertically. If you toe it in 15-20 degrees toward the centre of the audience, the on-axis energy misses the vocalist’s mic position entirely while still covering the room. Two speakers angled at each other also give you a wider sweet spot than two pointing straight ahead.

Watch the height, too. A speaker at ear height on a pole aimed slightly down throws sound over the audience’s heads and straight into the mic if the singer is tall. Get the horn at 1.7-1.9 m and aim it at the back row’s ear height.

What do you do when feedback still happens?

Find the frequency, then cut it narrowly. Push the channel fader until it rings, note the pitch, and cut 3-6 dB at that exact band with a narrow Q (around 4-8). One or two cuts like that will usually do it.

  • 500 Hz-1 kHz ring: usually the room, not the mic. Cut 2-3 dB.
  • 1.5-3 kHz ring: mic proximity to the speaker. Fix the position first.
  • 4-8 kHz squeal: a hot HF driver or a mic pointed at the horn. Check the horn angle.
  • Low 80-200 Hz boom: bass coupling with the floor. Lift the speaker on a pole or stand.

Does the speaker type change the strategy?

Yes. Self-powered boxes with good limiting are more forgiving because the limiter pulls level before the system goes fully unstable. A K-array KF12 self-powered 2-way speaker is a typical case: 90-degree dispersion, internal limiting, and no amp rack to set gain on in a hurry, which removes a whole class of mistakes.

Passive boxes with a shared amp can be harder, because adjusting one speaker’s level changes the others. If you run passive, label the amp channels clearly and set them once.

What about monitors — do they cause feedback too?

Almost always, in small rooms. A wedge pointed at a vocal mic from 0.5 m away is the shortest feedback path in the room. Two fixes: aim the wedge at the singer’s ears, not the face, and prefer a mic with a cardioid pattern null aimed toward the wedge. If the singer cups the mic, none of this works — cupping turns a cardioid into an omni and feedback is guaranteed.

Key Takeaways

  • Mains belong 1.5-2 m in front of vocal mics, never behind them.
  • Toe speakers in 15-20 degrees; horn height 1.7-1.9 m.
  • Doubling mic-to-speaker distance buys about 6 dB of margin.
  • Cut 3-6 dB at the ringing frequency with a narrow Q, not a wide shelf.
  • Wedges cause more feedback than mains in small rooms.