Description
This is a single EAW JF56 two-way full-range loudspeaker, used, in stock, and priced on request. It is the black portable version from EAW’s JF Series, the one built around neodymium components and a crossover that has aged better than most of what came out of 2010.
The rear panel says exactly what it is, and I would rather start there than with a marketing sentence. The printed label reads EAW / Eastern Acoustic Works / Whitinsville, MA USA / JF56, followed by a serial number and the terminal wiring for both powering modes. Below that: THIS PRODUCT HAS M10 MOUNTING POINTS. SEE OWNER’S MANUAL and a 2010 Loud Technologies copyright line.
What the JF56 actually is
The JF56 is a two-way full-range box with one 15-inch cone woofer in a vented chamber and a 1.4-inch exit compression driver on a horn. Coverage is 60 degrees horizontal by 45 degrees vertical, which is a deliberately tighter pattern than the 90 by 60 you see on most boxes in this class. That narrow pattern is the whole point of the JF Series: it throws further into a room before the walls start doing things you did not ask for.
Where it lands in practice: corporate A/V, small to medium live reinforcement, houses of worship, theatres, ballrooms, retail. Not a club sub, not a line array element, not a stage wedge by default although EAW sold adjustable legs for exactly that. It is the box you hang or pole-mount when you need one source to cover a defined seating area cleanly.
The numbers, from the factory sheet
I pulled EAW’s own JF56 specification sheet (part number RD0530, revision A00, October 2010) rather than rely on reseller pages, because reseller pages for this model are full of recycled numbers that belong to other boxes. What the sheet states:
- Configuration: LF, one 15-inch cone, vented loading. HF, one 1.4-inch exit compression driver with 3-inch voice coil, horn-loaded.
- Operating range: 47 Hz to 20 kHz.
- Nominal beamwidth: 60 degrees horizontal, 45 degrees vertical.
- Axial sensitivity: 98 dB LF/HF across the full range; HF alone 107 dB from 1300 Hz up.
- Impedance: 8 ohms nominal for LF/HF, LF alone, and HF alone. Minimum 6.4 ohms at 158 Hz in full-range mode.
- Recommended high pass: 40 Hz, 12 dB per octave Butterworth.
- Output limit: 126 dB average, 132 dB peak, calculated axial, whole space.
- Weight: approximately 35 kg, shipping weight approximately 40 kg.
One number to treat carefully: the accelerated life test on the sheet lists 72 volts for both LF and HF in the amp channels table. That is a test voltage, not a recommendation for what to hang on the terminals, and it reads as 650 W at 8 ohms for the LF section. Do not size an amplifier off that line and then wonder why the drivers complain.
Single-amp or bi-amp, your choice
The rear panel is switchable and the label spells out both wirings on a Neutrik Speakon pair. In single-amp mode, pins 1 carry the full-range signal. In bi-amp mode, pins 1 feed the low frequency section and pins 2 feed the high frequency section. The switch is on the connector panel, which is why the label bothers to print both options.
Practically: single-amp is the easy path with a passive crossover doing the work. Bi-amp needs a processor with the right crossover and, per EAW, DSP with EAW Focusing for the full benefit. If you run bi-amp without that processing you will get sound, but you will not get what the designer intended, and the HF driver is the part that suffers first. For a rental house running a mixed inventory, single-amp with a 40 Hz high pass is the sane default.
Rigging and mounting
The label states the cabinet has M10 mounting points, and the mechanical drawing shows them distributed across top and sides with a centre-of-balance mark. EAW sold the M10 by 37 mm forged shoulder eyebolt as an accessory, plus a U-bracket, adjustable legs for wedge duty, a flytrack segment, and cover plates that hide the handles and give the U-bracket something to grab.
Two handles are moulded into the sides. That sounds trivial until you have to lift 35 kg onto a pole at height, at which point it stops being trivial. Whoever installs this should read EAW’s manual for the load ratings before they hang it over anyone, because M10 points do not tell you the working load limit on their own.
Condition of this unit
The cabinets are the usual black textured coating with the moulded corner protectors, and the front is the perforated steel grille with the small red EAW badge at the bottom centre. On this unit the coating shows the honest marks of being moved: light scuffs on the corners, a few shallow scratches along the side edges, dust in the handle recesses. Nothing is punched in, no corner is split, and the grille is straight with no dents worth mentioning.
We opened one up to photograph the inside, so you can see what you are buying rather than take my word for it. The 15-inch neodymium woofer, the horn and compression driver, the passive crossover board in its white damping wadding, the Speakon connectors on the rear panel. The crossover caps and coils look undisturbed, no bulging, no scorch marks, no reflowed solder joints. The Speakon contact pins show normal tarnish from use, not corrosion.
What I cannot tell you: we have not measured impedance, we have not run a sweep, and I am not going to claim the drivers are matched to a tolerance I have not tested. If you want a specific measurement before it ships, name it and we will run it.
Related boxes in our stock
- RCF ART 310 active two-way 10-inch pair — smaller, powered, plug straight into a wall.
- JBL KP4010 passive two-way 10-inch — passive like the JF56 but a size down.
- Donbn DW12 passive 12-inch, set of three — budget fill for the same kind of room.
Shipping, export and price
In stock now and shipping from China. It is passive so there is no voltage question to solve, which makes export simpler than any powered box. We quote freight once you tell us the destination port and whether you want door delivery, and we can palletise multiple units.
Price on request. Send the destination and the quantity and you will get a figure with freight broken out separately.
Key takeaways
- EAW JF56 two-way full-range: one 15-inch vented LF, one 1.4-inch horn-loaded HF compression driver.
- 60 by 45 degree nominal coverage, 47 Hz to 20 kHz, 8 ohms, 98 dB axial sensitivity.
- Switchable single-amp or bi-amp on Speakon, rear panel marked for both.
- M10 mounting points top and sides; roughly 35 kg.
- Used, photographed inside and out, in stock, price on request.
