Description

One Adamson PLM 20K44, out of a touring rack. Front panel is the give-away: the PLM Series grille, the monochrome LCD, the rotary encoder, and the Lake processing badge next to a Dante certification mark. This is the 20K44 — four channels of Lab.gruppen-built power with Lake DSP on board, the box that drove a lot of Adamson S-Series and E-Series rigs before everyone moved to IPD and IPX.

Identification and serial

The rear panel serial reads 2021107 V108, which puts this unit in the 2021 production run. Four analog inputs on XLR with the Iso-Float transformer isolation, two AES/EBU ports on BNC, and the usual Adamson four-channel speaker output block on NL4.

Networking is the part worth looking at closely. There are two RJ45 ports marked LINK PRIM and LINK SEC, both 1 Gbps, plus a third switched port — that pair is what lets you run Dante redundancy or daisy-chain a rack without an external switch. If you are planning to drop this into an existing Dante network, that is the feature that matters.

Connectors, as photographed

  • Analog in: 4x XLR, Iso-Float isolated, pin 1 ground / pin 2 positive / pin 3 negative
  • Digital in: AES/EBU on BNC
  • Network: LINK PRIM 1 Gbps, LINK SEC 1 Gbps, plus a switched 100/1000 Base-T port
  • Speaker out: Adamson NL4 block, channels 1/4 and 2/3, with bridge markings for CH1&2 and CH3&4
  • Mains: Neutrik PowerCON TRUE1 inlet

Note the PowerCON TRUE1 rather than a plain IEC — that is the touring-standard locking inlet, and it means you can rack this next to your distro without an adapter.

Cosmetic condition

Straightforward honest assessment from the photos: light scratches on the top cover and around the rear panel fasteners, moderate dust in the vent grille and around the connectors. No dents, no bent rack ears, no missing screws, no burn marks or heat discoloration anywhere on the chassis. The rack ears are both present and straight.

That last point is not trivial. A 20K44 that has been dropped shows it immediately — bent ears, a distorted chassis, sometimes a cracked PCB that only shows up under load. This one has none of that.

The LCD is dark in the photos because the unit is not powered. Dust in the vents is surface dust, not caked-on, which usually means it came out of a rack and sat rather than ran in a smoky club for a decade.

What I have not tested

I have not powered this amplifier, loaded a Lake preset, or put a signal through any of the four channels. No load test, no Dante discovery test, no firmware check. I am not going to invent a “tested and working” line for a box this expensive to get wrong.

What I will do on request, before you commit:

  • Power it up and photograph the boot screen and firmware version
  • Show the Lake processor loading a preset
  • Confirm Dante discovery on the LINK PRIM port
  • Run a signal into each channel into a dummy load and report what the meters show
  • Shoot video of the whole sequence so you can see it live

Why a used PLM 20K44 still makes sense

Adamson has moved its current touring systems to the IPD and IPX platform, so the PLM series is legacy product. That cuts the resale price hard — good for you — but it does not make the hardware worse. The 20K44 is still a four-channel amplifier with Lake processing and Dante networking, and there is a large installed base of Adamson S-Series and E-Series cabinets that were designed around exactly this amp.

Where it fits: a rental house keeping an existing Adamson rig alive, a venue that needs a spare in the rack so a failure does not cancel a show, or anyone building a Dante-networked system who wants Lake DSP without buying new. Where it does not fit: someone starting from zero who could just as easily design around current product.

One practical note — the PLM series is out of production, so service means component-level repair rather than factory swap. That is worth knowing before you buy, and it is exactly the sort of thing I would want a seller to tell me.

Shipping and export

Ships from China, crated. A touring amplifier is heavy and rack-mount, so it goes as a boxed single unit or as part of a rack shipment if you are taking other gear. Tell us the destination port and we will quote both FOB and delivered terms.

Price is on request. For an untested legacy amplifier the number depends on what you need proven before it ships — say what testing you want and we will price against that.

Quick Summary

  • Model: Adamson PLM 20K44, four-channel touring amplifier
  • Serial: 2021107 V108 (2021 production)
  • Processing: Lake DSP with Dante certification
  • Inputs: 4x XLR analog Iso-Float, AES/EBU on BNC
  • Network: LINK PRIM + LINK SEC at 1 Gbps, plus switched port
  • Outputs: Adamson NL4 block, 4 channels with bridge options
  • Mains: Neutrik PowerCON TRUE1
  • Condition: good — light scratches and dust, no dents, ears straight, all screws present
  • Tested: no — not powered, no load test, no Dante check
  • Price: on request
  • Stock: in stock
Good In Stock

Adamson PLM 20K44 Four-Channel Touring Amplifier

Ask for price

FOB price from China. Shipping quoted per destination.

Listed on October 28, 2026
Learn more

Related Q&A & Guides