Daily Q&A

How to test a used microphone before you buy it?

Answered on October 29, 2026

Five minutes and a phone recording settle it. Speak into the mic at a fixed distance, tap the body lightly, wiggle the cable at both ends, and compare the level against a second mic you trust. Rattle, crackle or a big level mismatch are all deal-breakers that no cleaning will fix cheaply.

What should you test first?

Capsule rattle, because it is the one fault you cannot repair economically. Hold the mic a few centimetres from your ear and shake it gently along its axis. A faint tick is normal on some designs. A loose, shifting rattle means the diaphragm assembly has come adrift or the capsule mount has cracked. On a large-diaphragm condenser that is a $200-500 repair if the part still exists.

Then tap the grille with one fingernail. You should hear a dull, brief thud. A ringing ping or a rattle means something is loose inside.

How do you test the capsule with just your voice?

Record 20 seconds of speech at a fixed 20cm distance, then 20 seconds of breathing and hissing. Listen back on headphones for three things: low-frequency handling noise, a dull high end, and any intermittent crackle.

  • Dull top end on a condenser usually means moisture or dirt on the capsule. Sometimes it clears after 24 hours in a dry box; sometimes the capsule is done.
  • Crackle that stops when you move is cable or connector, not the mic. Cheap to fix, useful as a negotiating point.
  • Crackle that continues regardless is the capsule or the internal preamp. Walk.

Does the connector tell you anything?

XLR pins should be clean, straight and tight. Look for corrosion (green tint) and for a stretched pin that no longer grips the socket. A pin that has been bent and bent back is a weak point, and the fix is a $4 connector swap only if you can solder.

On dynamic mics like the Beyerdynamic Opus 29 S, also check the gooseneck: bend it through its full range and listen for a grinding feel. A gooseneck that has been bent too far is loose forever. We stock that model as new old stock, which is worth considering because a used gooseneck mic is the one category where the moving part is the whole point. Listings are on the Beyerdynamic Opus 29 S page.

How do you test phantom power gear?

Condensers need 48V, and a mic that works on a battery-powered preamp but not on phantom is telling you something. Test on a real phantom supply, not a cheap USB interface that only delivers 40V under load.

Some older condensers have been internally rewired for a specific manufacturer’s pinout. If a mic sounds thin and noisy on your interface but fine on the seller’s mixer, that is the likely reason.

What about wireless and USB microphones?

Wireless is a different risk profile. Check three things: the transmitter battery compartment for corrosion, the receiver’s RF scan (any dropouts within 5 metres means an antenna or front-end problem), and that the paired system matches serial numbers. Mismatched transmitter and receiver pairs work but drift.

USB mics are the category to avoid used. A failed USB controller is rarely repairable, the firmware is often proprietary, and drivers stopped being updated years ago on most models. Buy those new.

What is a fair price after testing?

Used dynamic mics hold value poorly: a $180 new SM58-style dynamic is $60-90 used. Condensers drop harder, typically 40-60% off, because buyers fear capsules. Anything that passes all the tests above and is a current model at 50% of new price is a fair deal. Anything with a documented fault should be priced accordingly, not sold as “Excellent”.

Key Takeaways

  • Shake test first: capsule rattle is the expensive, unfixable fault.
  • Record 20 seconds of speech and listen on headphones for dullness and crackle.
  • Crackle that responds to cable movement is a cheap fix and a good negotiating lever.
  • Test condensers on real 48V phantom, not a USB interface.
  • Skip used USB microphones entirely; controllers and drivers are not repairable.