Speak into it through headphones with the gain set 6 dB hot. Listen for a thin or dull top end, crackle when you tap the body, and self-noise with the capsule covered. Then check the connector and, for wireless, the RF section.
What is the 5-minute test anyone can do?
Plug it in, put on closed headphones, and set gain 6 dB hotter than you normally would. Speak six inches away. If the voice is thin, dull, or has a papery edge, the capsule has seen better days.
Then cover the grille with your palm and turn the gain up. Any hiss you hear is the electronics, not the room. A dynamic mic should be near silent. A condenser with audible hiss at normal gain is typically a tired capsule or a failing preamp in the mic itself.
Write the result down. Three mics tested in an afternoon blur together, and the one you liked at 2pm sounds different at 5pm. A one-line note per unit – bright, dull, noisy, clean – is enough.
Finally tap the body with a fingernail, lightly. You should hear a dull thud on the mains. A crackle or a dropout means a bad solder joint or a dirty switch, and both get worse.
How do you check a dynamic mic specifically?
Dynamics are simple and they age well. A Shure SM58 that has been dropped a hundred times usually still works, because the capsule is a coil in a magnetic gap with no circuit to fail.
Test it by cupping the grille and speaking close, then from 20 cm. A working SM58 keeps its low end when close and thins out predictably at distance. One that loses low end abruptly at close range has a partially collapsed surround.
The XLR connector is the other wear point. Look inside for a spread pin and a cracked plastic insert. A connector replacement is 5 USD in parts but it needs a soldering iron, and a cracked insert usually means the mic was dropped with a cable attached.
Check the thread and the grille. Cross-threaded grilles are common and a replacement ball grille is 10-15 USD, not a deal-breaker. A grille that will not unscrew at all usually means corrosion inside, and that is a walking-away sign.
What about condensers?
Ask for the year first. Condenser capsules lose sensitivity gradually, and nobody notices until they compare. If a 2010 condenser sounds 3-4 dB quieter than a 2022 one at the same gain, the diaphragm tension has relaxed.
Listen for sibilance. A worn large-diaphragm capsule often gets harsh around 6-8 kHz before it gets dull everywhere else. It sounds bright at first and unpleasant on the third take.
Check the output level switch and the pad. Those are mechanical and the first things to fail. Click each position and listen for the change.
How do you test a wireless handheld?
Bring your own headphones and your own cable. Half the mics that sound bad in a shop sound bad because the test cable has a broken screen, and you will never know whose fault it was.
RF first. Power the transmitter, set the receiver to the same frequency, and walk. A Shure UR2 handheld transmitter with Beta 58A capsules should hold a clean signal across a 30-metre room. Dropouts at 10 metres are a sign of a tired RF module or a counterfeit capsule.
Then check the capsule thread and the electronics. On the UR2 the capsule unscrews; look for cross-threading and for a gritty feel. A capsule that will not seat cleanly will crackle under handling noise.
Do the battery test twice. Once with a fresh cell and once with a cell at about 1.3 V, which is what a working transmitter actually sees most of the time. Cheap transmitters drop out early and you only find out mid-show.
Battery contacts matter more than people think. On older transmitters the spring contact loses tension and you get dropouts that look like RF problems. Wiggle a battery in the compartment and listen.
What should you never buy without testing?
Anything where the seller says tested but will not say how. The words are free. A specific test with numbers is what you are paying for.
Vintage condensers over 800 USD. Capsule condition is invisible and replacement capsules can cost 60% of the microphone’s value. If the seller cannot provide a recording, do not buy.
Wireless systems with the receiver but no transmitter, or the reverse. Mismatched pairs are almost impossible to complete later.
Anything sold as tested that arrives with the gain at a different setting from the photos. It means someone was in there after the photos were taken.
Key Takeaways
- Set gain 6 dB hot and listen through closed headphones; that exposes capsule wear in seconds.
- Cover the grille and raise gain to hear the mic’s own noise floor.
- Dynamic mics survive abuse; condensers lose sensitivity gradually and are hardest to judge.
- For wireless, walk 30 metres and check battery contacts before anything else.
