Description
The short answer: this is a pair of Meyer Sound 600-HP self-powered subwoofers, in stock, price on request. They are the high-power upgrade sub bass cabinet from the MINA line array system — two 15-inch long-excursion drivers per box, 1200 W AES of driver power each, 138 dB peak output at 1 metre, and usable response down to 36 Hz. Cabinets are complete and working, with their own amplification, TruPower limiting and protection built in.
What is the Meyer Sound 600-HP?
The 600-HP is Meyer Sound’s high-power companion sub for the MINA compact line array. Where the 500-HP covers compact jobs, the 600-HP is the version you spec when the venue needs real sub weight: bigger amplifier, more cone area, more output. Two long-excursion 15-inch drivers with 4-inch voice coils share one cabinet, and Meyer’s own two-channel class AB/H amplifier drives them with 2250 W continuous and 4500 W peak.
The cabinet is vented, made of heavy birch ply, and finished in the black textured coating Meyer uses on touring hardware. It is 1052 mm wide, 572 mm tall and 559 mm deep, and weighs around 100 kg — a two-person lift with handles, or a four-point hang with the MRF-600 rigging frame that is shared with the MINA array.
What are the specs people actually ask about?
| Brand | Meyer Sound |
| Model | 600-HP (high-power subwoofer) |
| Type | Self-powered vented subwoofer |
| Drivers | 2 × 15-inch long-excursion, 4-inch voice coil (1200 W AES each) |
| Amplifier | 2-channel class AB/H, 2250 W continuous / 4500 W peak with TruPower limiting |
| Frequency response | 36–150 Hz (±4 dB 36–130 Hz) |
| Maximum SPL | 138 dB peak @ 1 m |
| Connections | Balanced XLR loop-through, RMS network monitoring (hang version), PowerCon / L6-20 mains |
| Power supply | Universal wide-range AC input, self-adapting |
| Dimensions | 1052 × 572 × 559 mm |
| Weight | approx. 100 kg per cabinet |
| Rigging | MRF-600 frame or ground stack; shared with MINA |
Numbers like these are the reason the 600-HP holds value: 138 dB peak out of a box that hangs off the same bumper as the array above it.
Pair or single — what does two cabinets buy you?
Two 600-HPs give you options you do not get from one box. Side by side on the floor they couple below roughly 100 Hz, which buys about 3–6 dB of extra low end compared with a single cabinet in the same spot. Split them left and right and you get even coverage across a wide room instead of a low-end hot spot in the middle.
For a small-to-mid venue that runs MINA as the main hangs, two 600-HPs underneath is the balanced package: enough sub to carry a rock or DJ act, not so much that you need a bigger truck. If you are stacking them, keep the cabinets upright and remember they still want a little air around the vent — do not push them flat against a wall.
Self-powered — why does that matter for a used buy?
Because the expensive parts come with the cabinet. The amplifier, the processing and the limiter were matched to these drivers at the Meyer factory, so there is no amp rack to source, no crossover to program, and no risk of someone having paired the boxes with the wrong power. You supply mains and signal at line level and the cabinet does the rest.
It also makes the cabinets predictable in resale: a self-powered Meyer sub can be tested by any competent tech with a console and a couple of cables, which is exactly what we do before a cabinet leaves the warehouse.
What condition are these in?
Working, complete, and used. Both cabinets power up, both drivers are original and intact, and the grilles are straight. The textured finish carries the marks you would expect on rental stock: scuffs around the handle recesses and along the base where cabinets get dragged, some dust in the grille perforation. No dents in the cabinet panels, no missing handles, no ripped up corners.
The photos show the pair as they stand now. If you need something specific — a photo of a serial number, a measurement of a driver’s impedance, or a signal test on each cabinet — ask and we will do it and send the result before you pay anything.
What is a used pair worth?
Meyer Sound subwoofers do not lose their reputation with age. A used 600-HP in working order typically trades somewhere between USD 1,500 and USD 2,800 per cabinet depending on condition, vintage and whether the RMS monitoring hardware is present. Pairs move together because that is how people run them, and a matched pair usually fetches a small premium over two unrelated cabinets.
Price on this listing is on request. Send us the destination port and how you intend to use them — ground stacked under MINA hangs, or as stand-alone subs for a club or house of worship — and we will quote the pair together with freight.
Who should buy this pair?
Good fit: a rental house that already owns MINA or MICA tops and needs to add sub weight, a venue or church replacing a failed sub, a club that wants a proven high-output sub with its own amplification, or anyone building a MINA system piece by piece from the used market.
Poor fit: anyone who needs a compact single-18 that fits in a car, anyone running a 110 V venue without a step-up transformer, and anyone who wants a modern networked sub with software control. The 600-HP is analogue-era touring hardware — reliable, loud, and straightforward to service, but you tune a system, not an app.
Can it ship, and what about power?
Yes. Both cabinets go crated, roughly 120 kg each including packing, which is LCL groupage territory for most destinations rather than air unless you are close to a hub. They ship well as a pair on one pallet when lashed face to face with padding between the grilles — ask us to do that and we will.
Meyer’s wide-range supply handles 100–240 V, so most markets can run them from the wall. Check your mains connector: these use PowerCon or L6-20 depending on build, and a local cable is a five-minute fix, not a reason to pass on the pair.
Key Takeaways
- What it is: two Meyer Sound 600-HP self-powered subwoofers, the high-power sub for the MINA line array system.
- Specs: 2 × 15-inch drivers per cabinet, 1200 W AES each, 2250 W continuous amplification, 138 dB peak, 36 Hz low end.
- Price: on request, in stock in China. Typical used value USD 1,500–2,800 per cabinet.
- Condition: working pair, original drivers, cosmetic rental wear only.
- Power: wide-range AC input; check the mains connector type for your country.
Want a signal test, a freight quote, or more photos of a specific detail? Get in touch with the details and we will come back with a landed price. If you are assembling a full system, see our used Meyer Sound MINA line array listing for the tops that pair with these cabinets, or browse the rest of our used speaker stock.
