Three things kill a freshly imported used amplifier: wrong mains voltage, shipping shock to the solder joints, and a fault the seller already knew about. In that order. Voltage is the most common and the easiest to fix — one look at the rating plate behind the amp tells you in ten seconds.
I ship used power amps out of Shenzhen several times a month and this question lands in my inbox about twice a week. The pattern is boringly consistent, which is good news: you can pre-check all three causes before the amp ever leaves the warehouse.
Is the amp set for your voltage?
Professional amps generally come in three flavours: single-voltage (fixed 230 V or 120 V), dual-voltage with a rear switch, and auto-ranging switch-mode supplies. The first two are where people get burned.
Gear built for the Chinese market is set to 220 V / 50 Hz. UK and Europe run 230 V nominal, which is fine. The US is 120 V, and that is where a 220 V amp will fail — either the fuse blows instantly or, worse, it half-works and cooks its capacitors over three weeks.
- Check the plate: “AC 220V 50Hz” fixed means you need a transformer.
- Look for a voltage selector: many Crown, QSC and Yamaha amps have a slide switch or a jumper block.
- Auto-range: switch-mode amps from 2010 onward often take 100–240 V with no action needed.
If the amp is fixed at 220 V and you are on 120 V, you need a step-up transformer rated at least 1.5× the amplifier’s continuous draw. A 1,000 W amp needs a 1,500 VA transformer minimum. Undersized transformers sag under load and trip the amp’s protection — which reads exactly like a broken amplifier.
Did the shipping damage it?
Heavy linear amplifiers carry two big iron transformers and banks of 10,000 µF capacitors. Those parts weigh 4–8 kg each and are held by solder joints, not bolts. A 2-metre drop lands as a 20–40 g shock through the chassis, and the joints crack.
Symptoms of shipping shock: a buzz that appears only at high volume, intermittent channel dropout when the amp is warm, or a channel that cuts out when you tap the chassis. None of these show up in a 5-minute bench test at low level, which is why sellers pass them.
Fix cost is low — a tech reflows 6–12 joints for $60–$120. The pain is the diagnosis. Before you send it back, open the lid and look for cracked solder rings around the transformer leads and the big capacitor legs. A torch and five minutes will tell you.
Was the fault already there?
This is the awkward one. Common masked faults in the used market:
- One channel running 2–3 dB quieter, hidden by a gain knob turned up.
- A protection circuit that only trips after 40 minutes of real load.
- Fans replaced with cheap 12 V units that stall in warm rooms.
- Recapped poorly — mismatched capacitor brands on the same rail cause hum.
The cheap test is a 30-minute low-load run at 40% output into a dummy load, then a thermal check with an infrared thermometer. Output transistors should stabilise at 45–60 °C. Anything over 75 °C on one side only means imbalance.
What does a proper pre-shipment check look like?
| Check | Time | Pass criteria |
|---|---|---|
| Voltage plate match | 1 min | Matches destination mains |
| Both channels at 1 kHz, 10% power | 5 min | Within 0.5 dB |
| Dummy load run, 40% power | 30 min | No protection trip |
| Thermal check | 2 min | Under 65 °C |
| Visual on solder joints | 5 min | No cracked rings |
A seller who will not run that 45-minute sequence on a $900 amplifier is telling you something. I would rather pay $40 more to a seller who sends photos of the IR thermometer than save on one who says “tested, works great”.
Can you fix it yourself?
Voltage: yes, with the right transformer. Solder joints: no, unless you have done mains-level reflow before — the capacitor bank holds a lethal charge for hours after unplugging. Masked channel faults: no.
One rule I follow: never power up an imported amp on the first day at full volume. Run it at low level for an hour, then medium, then full. Faults that appear in the first hour are almost always shipping-related and fixable. Faults that appear in week three are usually the supply, not the amp.
Key Takeaways
- Voltage mismatch is the #1 cause — check the rating plate before anything else.
- Fixed 220 V amps need a transformer rated 1.5× the continuous draw.
- Linear amps crack solder joints in transit; buzzing at high volume is the tell.
- Run a 30-minute dummy-load test and an IR thermal check before paying.
- Never open a linear amplifier unless you know how to discharge the capacitor bank.
If you want a digital console that pairs cleanly with an imported amp rack, our Yamaha DM1000 digital mixing console runs on internal switching supplies and covers 100–240 V.
