To check a used audio system for sale properly, run four tests in order: impedance on every driver, a hum test with the source disconnected, a slow frequency sweep through each cabinet, and a 30-minute thermal run on the amplifier. Those four catch about 80% of what goes wrong after delivery.
Most buyers do the opposite. They play one track, hear sound, hand over cash. Sound coming out tells you almost nothing about whether a crossover capacitor is drying out or a voice coil is on its way to failure.
What does the impedance test tell you?
A multimeter across the terminals should read roughly 6-7 ohms on an 8-ohm nominal cabinet, or 3-4 ohms on a 4-ohm cabinet. That is the DC resistance, and it sits slightly below the nominal figure. If you read 2 ohms where 8 should be, a driver is shorted. If you read open circuit, something is disconnected.
Do this per cabinet, not per rig. A K-array KF12 that reads under 3 ohms when it should read near 6 has a problem in the amp module or a shorted driver, and no amount of good sound will fix that.
Why does a hum test catch more than a music test?
Play nothing at all and turn the gain up. A healthy system is silent or nearly so. A system with a failing ground or a leaky power supply hums at 50 or 60 Hz. Music masks that hum completely, which is why sellers always have music ready.
- Disconnect all sources, set gain to normal show level, listen for 30 seconds.
- Any steady hum means a power supply or grounding issue.
- Crackling with no signal points at a failing capacitor or dirty pot.
- Buzz that changes when you touch the chassis means a ground loop, often fixable.
How should you run a frequency sweep?
Use a sweep from 40 Hz to 16 kHz at moderate volume, one cabinet at a time. Listen for a cabinet that rattles on low notes, drops out in the midrange, or sounds dull above 10 kHz. Dull treble on a horn-loaded box usually means a tired compression driver diaphragm, which is a $120-200 part.
On the K-array KF12 self-powered speaker, the sweep also exercises the amp module’s protection circuit. If the limiter engages at levels far below spec, the module is degrading.
What is a thermal run and why does it matter?
Run the system at 70% of normal show level for 30 minutes, then put a hand near the amp heatsink. Warm is fine. Too hot to hold for two seconds means the thermal paste has dried out or the fan is failing. That is a common problem on 10-year-old powered boxes.
| Test | Time | Catches |
|---|---|---|
| Impedance per driver | 5 min | Shorted or open drivers |
| Hum test, no source | 1 min | PSU and grounding faults |
| Frequency sweep | 10 min | Weak drivers, bad crossovers |
| 30-min thermal run | 30 min | Cooling and amp degradation |
What paperwork should come with the system?
For an import purchase you want three documents: a commercial invoice with serial numbers listed, a packing list showing carton counts and weights, and a declaration stating the goods are used professional audio equipment. Missing serials on the invoice is the most common customs delay I see, and it can hold a shipment for two weeks.
Ask the seller for photos of every serial plate before shipping. Those photos are your only proof if one unit arrives dead and the seller claims it left in working order.
When should you walk away?
Walk if the seller refuses video of the sweep test, if the impedance numbers are not shared, or if the price is under 40% of market. Nothing about a used audio system is worth a blind purchase. The speakers category and shop page both list condition notes you can compare against.
Key Takeaways
- Four tests catch 80% of failures: impedance, hum, sweep, thermal run.
- An 8-ohm cabinet should read 6-7 ohms on a multimeter.
- Dull treble usually means a tired compression driver, a $120-200 part.
- Require serialized invoices; missing serials cause 2-week customs delays.
- No video of the sweep test means no deal.
